Skip to main content

アウディ A6 F2DKNF

Offset and wheel size calculator
for 19 inch wheels

Original Both axles

245/45R19

19x8.5J +40

Applies to: 4ドア・45TFSI クワトロ Sライン (2 variants · 2023/12–)

Some original sizes are unverified reference values.

Sizes may differ by year and grade. Also check the vehicle's placard and owner's manual. Data sources and licences →

Values shown are the original specifications registered for the new vehicle.They may differ from the sizes currently fitted. Choose the model code, year and grade, and compare with the tyre sidewall, wheel markings and the vehicle's specification.

On vehicles with different front and rear sizes, check the front and rear wheels separately.Don't treat a candidate for one axle as a recommendation for all four wheels. Check the front/rear combination, load capacity and pressure, mounting specification and the product's fitment information.

Frontis being edited. Front and rear settings are retained separately.

Even loaded original values may differ from a modified vehicle. Check the current setup against the actual installed dimensions, and compare staggered front/rear tyres separately.

Current wheel and tyre

19×8.5J / ET40·245/45R19Wheel Spacer 0mm / camber 0°

Wheel

Tyre and spacer

More settings and input options
Camber angle 0.0°
°

−10° to +10°. Negative angles tilt the top towards the vehicle. A blank input is treated as 0°.

Enter a complete size string

Replacement wheel and tyre

Wheel

Tyre and spacer

More settings and input options
Quick settings and presets

The +1/+2 inch presets choose a tyre with a similar diameter and a wheel whose outer edge stays close to the original position, with less than 10 mm additional inward movement.

Camber angle 0.0°
°

−10° to +10°. Negative angles tilt the top towards the vehicle. A blank input is treated as 0°.

Enter a complete size string
Calculate offset from a target position
mm

Enter 10 for 10 mm outwards or −5 for 5 mm inwards. The inverse calculation includes rim width and both spacer thicknesses at 0° camber. It does not set tyre-sidewall or actual fender position. Blank spacers are treated as 0 mm.

Outer edge unchanged

Inner clearance unchanged

This is movement from the current rim position, not the remaining clearance.Positions are compared at 0° camber. Actual inner clearance is unknown; inspect the vehicle for interference and fitment.

Cross-section

Front: Double wishbone

Wheel and tyre cross-section: current versus replacement Outer edge unchanged、Inner edge unchanged; diameter difference ±0.0mm
  • Current
  • Replacement
  • Fender
  • The wheel and tyre are approximate sections based on the entered dimensions. The vertical dashed line marks the hub mounting face.Suspension drawings are generic references. Brake and knuckle angles follow replacement camber. Drawn gaps do not represent actual clearances or establish fitment.
Current rim width / offset
8.5 in / +40.0mm
Replacement rim width / offset
8.5 in / +40.0mm
Outer rim-edge movement
Outer edge unchanged
Inner rim-edge movement
Inner edge unchanged
Tyre diameter difference
±0.0mm

Rim width describes the tyre-supporting width. Offset is the distance from its centre to the mounting face. Increasing width extends both edges; changing offset shifts the whole assembly. Movement also includes the spacer-thickness difference.

Rim width, offset and worked example
Rim-width and offset references
Rim width (between bead seats)Positive offset

Vehicle side is left; outside is right. The grey dashed line is rim centre and the blue dashed line is the hub mounting face. Rim width is not overall flange-to-flange width. This schematic is not drawn to a constant scale.

Example: from 6 inches / +45 mm to 7 inches / +48 mm, half the width increase is 12.7 mm. The outer edge moves out by 12.7−3 = 9.7 mm; the inner edge moves towards the vehicle by 12.7+3 = 15.7 mm. This hypothetical example has no spacers and 0° camber.

Ride-height change from tyre diameter
±0.0mm
Change in gap above tyre
±0.0mm

Positive values mean higher ride height or a larger gap; negative means lower or smaller. This estimate uses half the diameter difference at 0° camber with unchanged suspension settings, without tyre deflection under load.

Upper-edge position with camber

Upper-edge position with camber

Current 0.0° → replacement 0.0°

Movement of upper outer point
±0.0mm
Horizontal upper-edge distance to fender
20.4mm
Vertical upper-edge distance to fender
30.8mm

This reference rotates the section about the hub centre. Tyre shoulder shape, deflection and suspension movement are excluded. Movement dimensions and the existing fender assessment use 0° camber.

Fender OK (estimated)

Positive values indicate outward/inward movement as labelled. Values are changes from the current setup.

How to measure inner clearance

These fixed explanatory diagrams do not change with the inputs.

The box is shown as a section across the wheel width. The blue line joins the strut-tube surface and inner rim-flange edge at the same height. Inward movement is not remaining clearance.

One strut assembly and enlarged detail
One front MacPherson strut wheel. The dashed box marks where the tube and rim approach each other.
Part legend (10 items)
  1. Upper mounting point
  2. Upper spring seat
  3. Coil spring
  4. Lower spring seat
  5. Strut tube
  6. Strut-to-knuckle joint
  7. Steering knuckle
  8. Hub and bearing connection
  9. Lower ball joint
  10. Lower control arm
Distance from tube surface to inner rim edge at the same height
The blue line joins the strut-tube surface and inner rim-flange edge at equal height.

Check tyre-sidewall, spring-seat and spoke-to-caliper clearances separately.

Omitted parts and physical checks

This typical strut schematic does not reproduce actual dimensions or establish fitment. Brakes, driveshaft, tie rod, anti-roll bar and mounting brackets are omitted but also require clearance checks. Clearance changes with ride height, steering and load. Part numbers are legend references, not measurement points.

Fender positionAssessment uses a position estimated from the original size

Fender calculations use the nominal wheel-size reference. This differs from the physical rim edge; do not enter an edge measurement without checking the reference.

If a value is unknown, keep the estimate as a reference. An estimate does not establish fitment.

mm
mm
Estimate assumptions

From the outside of the current (original) tyre: 20mm outwards and above the upper edge by 30mm above the reference point. This is a common assumption, not a vehicle measurement.

Choose Clear fender position to disable the assessment.

View reference points and measurement locations

These fixed explanatory diagrams do not change with the inputs.

Locate measurements on the assembly
One wheel and its fender. The box identifies the area shown in the enlarged section below.

An enlarged section cuts across the wheel width. It is not simply a zoom of the same viewing angle.

Measured reference: physical rim edge
The blue circle marks the physical flange edge. Measure horizontal and vertical distances to the same fender edge.
Nominal reference: a position calculated from size markings
The purple diamond marks the nominal-size reference. Use distances from this point, not directly from the physical edge.

Use the distance from the purple reference. The vertical distance is between stationary points, not remaining tyre clearance while driving.

Nominal dimensions and measurement corrections

Nominal rim width is normally measured between bead seats, and nominal diameter at the tyre seat. These references can be difficult to measure on an installed wheel. Any correction from a physical edge requires product dimensions or a measured basis. No universal correction or automatic conversion is applied.

Compare candidates A, B and C Front·0/3

Keep up to three replacement candidates per axle during this page visit. Reloading or changing vehicle/specification clears them; they are not included in shared URLs or restored inputs. Use Save in My garage to keep a setup.

Candidates are recalculated against the current setup. Movement is the rim-edge difference at 0° camber, not a determination of physical clearance or fitment.

  • CandidateA

    No saved comparison candidates yet.

  • CandidateB

    No saved comparison candidates yet.

  • CandidateC

    No saved comparison candidates yet.

Save the vehicle, grade and measured fender references. Use its My vehicles shortcut next time.

Save the current setup for both axles and compare it in My garage.

Detailed results and fender assessmentDiameter, circumference, calculated speed and fender margins

Wheel position changes

Outside (outer rim edge)
±0.0mm
Outer edge unchanged
Inside (inner rim edge)
±0.0mm
Inner edge unchanged

Outer tyre sidewall ±0.0mm / inner ±0.0mm

Fender

OK
Lateral wheel margin
35.0mm
Lateral tyre margin
20.4mm
Difference at tyre top
30.8mm

Tyre diameter and speedometer

Diameter difference
±0.0mm
±0.0%
At an indicated 100 km/h
100.0km/h
Calculated road speed
Shaken guide (Japan) OK Within comparison range(−1%〜+3%)
Current Replacement The inner lines represent the wheel (rim)
DiameterCircumferenceSidewall
Current 245/45R19 703.1mm 2,208.9mm 110.3mm
Replacement 245/45R19 703.1mm 2,208.9mm 110.3mm
Speedometer conversion
Indicated speedCalculated road speedDifference
40km/h 40.0km/h ±0.0km/h
60km/h 60.0km/h ±0.0km/h
80km/h 80.0km/h ±0.0km/h
100km/h 100.0km/h ±0.0km/h

This assumes the speedometer is accurate with the original tyres.

Share this setup

Post the setup on X or send its URL. The link retains both axle setups, spacer thickness, camber, vehicle selection and diagram view.

Text for X

アウディ A6(F2DKNF) Front: 19x8.5J +40·245/45R19 Rear: 19x8.5J +40·245/45R19
#FITMENTLAB

The short link stores the current front and rear setups. Later edits do not change an already shared link.

Outwards
0.0mm
Diameter
±0.0%
✓ OK Tyre options →

Related calculations with this original size

The registered grade and front/rear original sizes are carried over. Check the sizes actually fitted and which wheels are driven. Where gear ratios or the final drive ratio are not registered, replace the example values in the calculator with your vehicle's figures.

Applies to: 4ドア・45TFSI クワトロ Sライン (4WD, 7AT) 2024/10–. With different front and rear sizes, speed and rpm calculations use the tyre diameter on the driven axle. For four-wheel-drive vehicles, also check the manufacturer's limits on front/rear circumference difference.

FITMENT

Requirements for aftermarket wheels

PCD and studs
5H-112
Centre bore
66.5mm or larger

Only wheels with the same PCD and stud count will fit. If a wheel has a larger centre bore, filling the gap with a hub ring helps prevent vibration.

INCH UP

Plus-size options

Sizes with a diameter close to the original 245/45R19. Tap Calculate to load one into the calculator above and check the protrusion.

20 inch

21 inch

See options including tyre models →

WINTER TIRES

Smaller wheel options for winter (studless) tyres

A wheel 1 inch smaller than the original 245/45R19 makes the tyre and wheel set cheaper and lets you choose a taller-sidewall tyre that is easier to handle on snow. These sizes have a diameter close to the original.

On vehicles with large brake calipers, a smaller wheel may hit the brakes and not fit. When choosing wheels, check fitment for your vehicle with the retailer. “Calculate” shows the change in rim position from the entered dimensions; it cannot calculate the actual brake clearance. Also check load capacity, approved rim width and product availability. For vehicles with different front and rear sizes, check whether the reference size is front or rear and check the front/rear combination separately.

REFERENCE

Reference figures for this vehicle

Track front / rear
1,625mm / 1,610mm
Width
1,885mm
Vehicle weight
1,780kg
Max. power
265PS
Min. turning radius
5.7m
Suspension front / rear
ダブルウィッシュボーン式 / ダブルウィッシュボーン式
Brakes front / rear
ディスク / ディスク

Vehicle weight is a guide for the tyre load index; track width is a guide for side-to-side protrusion.

BY GRADE

Grades with this original size

2 variants

OTHER SIZES

Other original sizes for the A6 F2DKNF

FAQ

FAQ: cars with 19 inch wheels

Tap a question to show the answer.

What is the original offset for the A6 (F2DKNF) with 19 inch wheels?

The original 19x8.5J +40 wheel has an offset of +40. In Japan, offset is now officially called “inset”. Reducing the offset by 1 moves the wheel 1 mm outwards (with the same rim width).

How far can the A6 (F2DKNF) with 19 inch wheels go up in wheel size?

To keep the diameter close to the original (245/45R19), guide sizes are 20 inch: 245/40R20, 21 inch: 245/35R21. Whether they actually fit depends on rim width, offset and fender clearance. Check the protrusion with the calculator on this page.

How do I get a flush fitment on the A6 (F2DKNF) with 19 inch wheels?

Measure the lateral gap between the fender lip and the outside of the tyre, then choose a rim width and offset that move the wheel out by that amount. If you have not measured it, the calculator on this page checks against a fender position estimated from the original size (the estimate errs on the safe side).

Which aftermarket wheels fit the A6 (F2DKNF) with 19 inch wheels?

Wheels with a 5H-112 PCD and stud count and a centre bore of 66.5mm or larger. If the wheel's centre bore is larger, filling the gap with a hub ring helps prevent vibration.

All original sizes for the A6 F2DKNF
TOP