Skip to main content

WHEEL BASICS

Wheel basics

The essentials of size, mounting and safety for choosing aftermarket wheels. For the final word on whether they fit, use the calculator and fitment charts.

Reading the size marking

17×7J +48 5H-114.3

17
Rim diameter (inches). Must match the tyre's rim diameter
7J
Rim width (inches). J is the shape of the rim flange
+48
Inset / offset (mm). Distance from the wheel centreline to the mounting face
5H
Number of bolt holes (5)
114.3
PCD (diameter of the circle through the bolt-hole centres, mm)

How to read tyre and wheel sizes (illustrated) →

Inset and rim width change where the wheel sits

Every 1 less inset moves the wheel 1 mm outwards. Widening the rim by 1 inch (25.4 mm) at the same inset adds half (about 12.7 mm) on each side, inner and outer. In Japan this value used to be called “offset”, and some manufacturers write it as “ET48”.

  • Too far out: pokes out past the wheel arch (fails Japan's shaken vehicle inspection) and the tyre rubs on the arch
  • Too far in: hits the suspension or brakes (callipers)
What is “shaken”? (Japan’s vehicle inspection)

Shaken (車検) is Japan’s compulsory roadworthiness inspection. A typical private car is first inspected three years after it is first registered, and every two years after that. A car without a valid shaken certificate cannot be driven on public roads in Japan.

The inspection checks that the car still meets Japan’s vehicle safety standards. For wheels and tyres, this includes whether the tyres stick out beyond the bodywork, whether the tyres have enough load capacity, and whether the speedometer still reads within the permitted range after a size change.

Shaken costs combine fixed government charges (vehicle weight tax, compulsory third-party insurance known as jibaiseki, and inspection fees) with any repair or service charges from the workshop.

This is a Japan-only system. If your car is registered in another country, follow that country’s roadworthiness and vehicle modification rules instead; this site’s pass/fail guides do not apply there.

Calculate how many mm it moves versus stock →

PCD and studs

The stud count and PCD must match your car exactly, or the wheel will not fit. Most Japanese-market passenger cars use “5H-114.3” and many compact cars and kei cars use “4H-100”, but it varies by model and year even within one manufacturer (e.g. 5H-100, 5H-112). You can look up your car's values under Vehicles.

Centre bore and hub rings

The hole in the centre of the wheel (centre bore) must be the same size as the car's hub or larger, or it will not fit. Aftermarket wheels are often made with a larger bore to fit many cars, and a hub ring fills the gap. It helps centre the wheel on the car and prevent vibration at high speed.

Nut and bolt seats, and tightening

The surface where a nut (or bolt) contacts the wheel is called the seat, and you must use nuts with the same seat shape as the wheel. Most aftermarket wheels use a “60° taper seat”, so flat-seat or ball-seat nuts for original wheels may not be usable as they are. The thread diameter and pitch (e.g. M12×P1.5) must also match the car.

  • Tighten gradually in a criss-cross pattern to the torque given in the owner's manual
  • After driving for a while, re-torque the nuts (check they have not loosened)

JWL and VIA marks

JWL is a mark the manufacturer applies after its own testing, showing that an alloy (light-alloy) wheel for passenger cars meets Japan's national technical standard (JWL-T for trucks, buses and commercial vehicles). VIA is given to wheels whose compliance has been confirmed by an independent testing body. Choose alloy wheels marked JWL (or JWL-T).

Weight and construction (cast vs forged)

Wheels are unsprung, rotating parts, so lighter wheels benefit acceleration, braking and ride comfort. Cast wheels, made by pouring molten metal into a mould, come in many designs at affordable prices; forged wheels, shaped from metal under pressure, are lighter and stronger but expensive. Plus-sizing tends to add weight, so once you have settled on a size, compare weights too.

Checking fitment

  1. 1. Mounting: same stud count and PCD, centre bore the same or larger, matching nut seat and thread
  2. 2. Position: with the rim width and inset, it neither pokes out nor hits anything inside (use this site's inset calculator)
  3. 3. Manufacturer's fitment chart: for things a calculation cannot show, such as calliper clearance, use the wheel maker's vehicle-specific fitment chart

Vehicle pages and product lists show candidates matched against registered dimensions and mounting specifications. A dimensional match does not guarantee that the wheel will fit the actual car. Products with missing data such as centre bore need checking. Confirm the nut/bolt specification, spoke and rim clearance to the brakes, and any contact when steering or as the suspension moves using the manufacturer's fitment chart and the actual car.

Check for poke with the wheel size you're considering

Pick your vehicle to fill in the original size, then just enter the new rim width and inset. A cross-section diagram shows how many mm it moves out from stock and whether it pokes past the wheel arch.

Original sizes by model code and grade, plus-size and winter minus-size options, and shortcuts to the inset calculator.

Manufacturer sources

Figures are general guidelines. Before fitting, check the wheel manufacturer's fitment chart and with your dealer.

TOP