Jaguar Fpace DC2XB
Offset and wheel size calculator
for 18 inch wheels
Applies to: Pure, Prestige, Portfolio (15 variants · 2017/12–)
Some original sizes are unverified reference values.
Sizes may differ by year and grade. Also check the vehicle's placard and owner's manual. Data sources and licences →
Values shown are the original specifications registered for the new vehicle.They may differ from the sizes currently fitted. Choose the model code, year and grade, and compare with the tyre sidewall, wheel markings and the vehicle's specification.
On vehicles with different front and rear sizes, check the front and rear wheels separately.Don't treat a candidate for one axle as a recommendation for all four wheels. Check the front/rear combination, load capacity and pressure, mounting specification and the product's fitment information.
Frontis being edited. Front and rear settings are retained separately.
Even loaded original values may differ from a modified vehicle. Check the current setup against the actual installed dimensions, and compare staggered front/rear tyres separately.
The original rim width or offset is not registered for this vehicle. Enter the markings on the actual wheel (for example, 16x6.5J +45) in the current setup.
Current wheel and tyre
18×—J / ET—·255/60R18Wheel Spacer 0mm / camber 0°
Wheel
Tyre and spacer
More settings and input options
Camber angle 0.0°
−10° to +10°. Negative angles tilt the top towards the vehicle. A blank input is treated as 0°.
Enter a complete size string
Replacement wheel and tyre
Wheel
Tyre and spacer
More settings and input options
Quick settings and presets
The +1/+2 inch presets choose a tyre with a similar diameter and a wheel whose outer edge stays close to the original position, with less than 10 mm additional inward movement.
Camber angle 0.0°
−10° to +10°. Negative angles tilt the top towards the vehicle. A blank input is treated as 0°.
Enter a complete size string
Calculate offset from a target position
How to measure inner clearance
These fixed explanatory diagrams do not change with the inputs.
The box is shown as a section across the wheel width. The blue line joins the strut-tube surface and inner rim-flange edge at the same height. Inward movement is not remaining clearance.
Part legend (10 items)
- Upper mounting point
- Upper spring seat
- Coil spring
- Lower spring seat
- Strut tube
- Strut-to-knuckle joint
- Steering knuckle
- Hub and bearing connection
- Lower ball joint
- Lower control arm
Check tyre-sidewall, spring-seat and spoke-to-caliper clearances separately.
Omitted parts and physical checks
This typical strut schematic does not reproduce actual dimensions or establish fitment. Brakes, driveshaft, tie rod, anti-roll bar and mounting brackets are omitted but also require clearance checks. Clearance changes with ride height, steering and load. Part numbers are legend references, not measurement points.
Fender positionAssessment uses a position estimated from the original size
Fender calculations use the nominal wheel-size reference. This differs from the physical rim edge; do not enter an edge measurement without checking the reference.
If a value is unknown, keep the estimate as a reference. An estimate does not establish fitment.
Estimate assumptions
From the outside of the current (original) tyre: 20mm outwards and above the upper edge by 30mm above the reference point. This is a common assumption, not a vehicle measurement.
View reference points and measurement locations
These fixed explanatory diagrams do not change with the inputs.
An enlarged section cuts across the wheel width. It is not simply a zoom of the same viewing angle.
Use the distance from the purple reference. The vertical distance is between stationary points, not remaining tyre clearance while driving.
Nominal dimensions and measurement corrections
Nominal rim width is normally measured between bead seats, and nominal diameter at the tyre seat. These references can be difficult to measure on an installed wheel. Any correction from a physical edge requires product dimensions or a measured basis. No universal correction or automatic conversion is applied.
Compare candidates A, B and C Front·0/3
Keep up to three replacement candidates per axle during this page visit. Reloading or changing vehicle/specification clears them; they are not included in shared URLs or restored inputs. Use Save in My garage to keep a setup.
Candidates are recalculated against the current setup. Movement is the rim-edge difference at 0° camber, not a determination of physical clearance or fitment.
-
CandidateA
No saved comparison candidates yet.
-
CandidateB
No saved comparison candidates yet.
-
CandidateC
No saved comparison candidates yet.
Detailed results and fender assessmentDiameter, circumference, calculated speed and fender margins
Tyre diameter and speedometer
- Diameter difference
- ±0.0mm
- ±0.0%
- At an indicated 100 km/h
- 100.0km/h
- Calculated road speed
| Diameter | Circumference | Sidewall | |
|---|---|---|---|
| Current 255/60R18 | 763.2mm | 2,397.7mm | 153.0mm |
| Replacement 255/60R18 | 763.2mm | 2,397.7mm | 153.0mm |
| Indicated speed | Calculated road speed | Difference |
|---|---|---|
| 40km/h | 40.0km/h | ±0.0km/h |
| 60km/h | 60.0km/h | ±0.0km/h |
| 80km/h | 80.0km/h | ±0.0km/h |
| 100km/h | 100.0km/h | ±0.0km/h |
This assumes the speedometer is accurate with the original tyres.
Related calculations with this original size
The registered grade and front/rear original sizes are carried over. Check the sizes actually fitted and which wheels are driven. Where gear ratios or the final drive ratio are not registered, replace the example values in the calculator with your vehicle's figures.
Applies to: Pure (8AT) 2019/10–. With different front and rear sizes, speed and rpm calculations use the tyre diameter on the driven axle. For four-wheel-drive vehicles, also check the manufacturer's limits on front/rear circumference difference.
The PCD and stud count are incomplete, so no search link with the mounting specification is shown. Check your vehicle's specified values.
Calculators available for this grade →REFERENCE
Reference figures for this vehicle
- Track front / rear
- 1,640mm / 1,655mm
- Width
- 1,935mm
- Vehicle weight
- 1,920kg
- Max. power
- 250–300PS
- Min. turning radius
- 5.6m
- Suspension front / rear
- Double wishbone / Integral link
- Brakes front / rear
- Ventilated disc / Ventilated disc
Vehicle weight is a guide for the tyre load index; track width is a guide for side-to-side protrusion.
BY GRADE
Grades with this original size
15 variants
- Pure (8AT)2019/10–
- Prestige (8AT)2019/10–
- Pure (8AT)2019/10–
- Portfolio (8AT)2019/10–
- Prestige (8AT)2019/10–
- Portfolio (8AT)2019/10–
- Pure (8AT)2018/12–
- Prestige (8AT)2018/12–
- Portfolio (8AT)2018/12–
- Pure (8AT)2018/12–
- Prestige (8AT)2018/12–
- Portfolio (8AT)2018/12–
- Pure (8AT)2017/12–
- Prestige (8AT)2017/12–
- Portfolio (8AT)2017/12–
OTHER SIZES
Other original sizes for the Fpace DC2XB
FAQ
FAQ: cars with 18 inch wheels
Tap a question to show the answer.
How far can the Fpace (DC2XB) with 18 inch wheels go up in wheel size?
To keep the diameter close to the original (255/60 R18), guide sizes are 19 inch: 255/55R19, 20 inch: 255/50R20. Whether they actually fit depends on rim width, offset and fender clearance. Check the protrusion with the calculator on this page.
How do I get a flush fitment on the Fpace (DC2XB) with 18 inch wheels?
Measure the lateral gap between the fender lip and the outside of the tyre, then choose a rim width and offset that move the wheel out by that amount. If you have not measured it, the calculator on this page checks against a fender position estimated from the original size (the estimate errs on the safe side).