Wheel Offset & Tyre Diameter Calculator
Wheel offset is the ET value marked on a wheel, such as +45 or ET45.
Load original sizes from a vehicle, or enter the current and replacement dimensions manually.
What this calculator can do
- Enter current and replacement wheel spacer thicknesses in mm; their difference is included in inward and outward movement.
- Set and retain front and rear wheel, tyre and spacer dimensions independently, including staggered sizes.
- Compare current and replacement wheel and tyre positions in an SVG cross-section that updates with the inputs.
- Fixed structural diagrams explain rim-width, offset and clearance measurement references. These illustrations do not change with the inputs.
Selected vehicle: BMWアルピナ XD4 MU30 オールラッド (8AT) · 2022/11–
Frontis being edited. Front and rear settings are retained separately.
Even loaded original values may differ from a modified vehicle. Check the current setup against the actual installed dimensions, and compare staggered front/rear tyres separately.
The original rim width or offset is not registered for this vehicle. Enter the markings on the actual wheel (for example, 16x6.5J +45) in the current setup.
Current wheel and tyre
20×—J / ET—·255/45R20Wheel Spacer 0mm / camber 0°
Wheel
Tyre and spacer
More settings and input options
Camber angle 0.0°
−10° to +10°. Negative angles tilt the top towards the vehicle. A blank input is treated as 0°.
Enter a complete size string
Replacement wheel and tyre
Wheel
Tyre and spacer
More settings and input options
Quick settings and presets
The +1/+2 inch presets choose a tyre with a similar diameter and a wheel whose outer edge stays close to the original position, with less than 10 mm additional inward movement.
Camber angle 0.0°
−10° to +10°. Negative angles tilt the top towards the vehicle. A blank input is treated as 0°.
Enter a complete size string
Calculate offset from a target position
How to measure inner clearance
These fixed explanatory diagrams do not change with the inputs.
The box is shown as a section across the wheel width. The blue line joins the strut-tube surface and inner rim-flange edge at the same height. Inward movement is not remaining clearance.
Part legend (10 items)
- Upper mounting point
- Upper spring seat
- Coil spring
- Lower spring seat
- Strut tube
- Strut-to-knuckle joint
- Steering knuckle
- Hub and bearing connection
- Lower ball joint
- Lower control arm
Check tyre-sidewall, spring-seat and spoke-to-caliper clearances separately.
Omitted parts and physical checks
This typical strut schematic does not reproduce actual dimensions or establish fitment. Brakes, driveshaft, tie rod, anti-roll bar and mounting brackets are omitted but also require clearance checks. Clearance changes with ride height, steering and load. Part numbers are legend references, not measurement points.
Fender positionAssessment uses a position estimated from the original size
Fender calculations use the nominal wheel-size reference. This differs from the physical rim edge; do not enter an edge measurement without checking the reference.
If a value is unknown, keep the estimate as a reference. An estimate does not establish fitment.
Estimate assumptions
From the outside of the current (original) tyre: 20mm outwards and above the upper edge by 30mm above the reference point. This is a common assumption, not a vehicle measurement.
View reference points and measurement locations
These fixed explanatory diagrams do not change with the inputs.
An enlarged section cuts across the wheel width. It is not simply a zoom of the same viewing angle.
Use the distance from the purple reference. The vertical distance is between stationary points, not remaining tyre clearance while driving.
Nominal dimensions and measurement corrections
Nominal rim width is normally measured between bead seats, and nominal diameter at the tyre seat. These references can be difficult to measure on an installed wheel. Any correction from a physical edge requires product dimensions or a measured basis. No universal correction or automatic conversion is applied.
Compare candidates A, B and C Front·0/3
Keep up to three replacement candidates per axle during this page visit. Reloading or changing vehicle/specification clears them; they are not included in shared URLs or restored inputs. Use Save in My garage to keep a setup.
Candidates are recalculated against the current setup. Movement is the rim-edge difference at 0° camber, not a determination of physical clearance or fitment.
-
CandidateA
No saved comparison candidates yet.
-
CandidateB
No saved comparison candidates yet.
-
CandidateC
No saved comparison candidates yet.
Detailed results and fender assessmentDiameter, circumference, calculated speed and fender margins
Tyre diameter and speedometer
- Diameter difference
- ±0.0mm
- ±0.0%
- At an indicated 100 km/h
- 100.0km/h
- Calculated road speed
| Diameter | Circumference | Sidewall | |
|---|---|---|---|
| Current 255/45R20 | 737.5mm | 2,316.9mm | 114.8mm |
| Replacement 255/45R20 | 737.5mm | 2,316.9mm | 114.8mm |
| Indicated speed | Calculated road speed | Difference |
|---|---|---|
| 40km/h | 40.0km/h | ±0.0km/h |
| 60km/h | 60.0km/h | ±0.0km/h |
| 80km/h | 80.0km/h | ±0.0km/h |
| 100km/h | 100.0km/h | ±0.0km/h |
This assumes the speedometer is accurate with the original tyres.
HOW WE CALCULATE
How wheel offset and tyre diameter are calculated
Wheel position change
Convert rim width to mm. Without spacers, outward movement = (replacement width − current width) × 25.4 ÷ 2 − (replacement offset − current offset). A positive result means outward movement.
Tyre diameter change
Nominal diameter (mm) = rim diameter (inches) × 25.4 + tyre width (mm) × aspect ratio ÷ 100 × 2. Actual dimensions vary by manufacturer, model and condition.
This is a dimensional comparison, not a fitment determination. Check load capacity, approved rim width, brakes and suspension clearance separately.
Example: 6J / +45 to 7J / +40
Without spacers, the outer edge moves out by 17.7 mm and inner clearance decreases by 7.7 mm. Separate half the width increase (12.7 mm) from the 5 mm offset decrease. Tyre protrusion need not equal rim-edge movement.
Example: 195/65R15 to 205/55R16
Nominal diameter changes from 634.5 mm to 631.9 mm: −2.6 mm (about −0.41%). Assuming the original speedometer is accurate, an indicated 100 km/h converts to about 99.6 km/h.
Is the calculated speed a measured road speed?
Converted speed = indicated speed × replacement diameter ÷ original diameter. Original speedometer error, pressure, load, wear and rolling-circumference differences are excluded. This is not a measured road speed or a guarantee of passing shaken (Japan's vehicle inspection).
What is “shaken”? (Japan’s vehicle inspection)
Shaken (車検) is Japan’s compulsory roadworthiness inspection. A typical private car is first inspected three years after it is first registered, and every two years after that. A car without a valid shaken certificate cannot be driven on public roads in Japan.
The inspection checks that the car still meets Japan’s vehicle safety standards. For wheels and tyres, this includes whether the tyres stick out beyond the bodywork, whether the tyres have enough load capacity, and whether the speedometer still reads within the permitted range after a size change.
Shaken costs combine fixed government charges (vehicle weight tax, compulsory third-party insurance known as jibaiseki, and inspection fees) with any repair or service charges from the workshop.
This is a Japan-only system. If your car is registered in another country, follow that country’s roadworthiness and vehicle modification rules instead; this site’s pass/fail guides do not apply there.
Which axle should I enter for staggered tyres?
Compare front and rear movement and clearance separately. One axle's result is not a fitment recommendation for all four wheels. Use driven-wheel diameter for speed/RPM calculations, and check manufacturer limits for front/rear circumference differences on AWD vehicles.